Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
We have unearthed this great article relating to Installing A Bathtub directly below on the internet and believe it made sense to discuss it with you on this site.
Setting up a bath tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard task. If the old tub is readily easily accessible, the job can move speedily; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to move out the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the task and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a new bath tub in your bathroom if you have actually currently purchased a brand-new tub as well as do not need to transform the setup of your previous supply of water pipelines.
Your devices and product list ought to consist of the following:
Preparing for the Setup
To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, place the bathtub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To set up taps, fit all-time low of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bathtub and additionally check the overflow electrical outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been made use of at least once as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in area in between the tap and the sink. Protect the tap in position with the supplier given backnut. Once the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former type ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that write-up about How to Install a Bathtub Yourself from a good friend on a different web address. Are you aware of someone else who is in the market for Installing A Bathtub? Do not hesitate to share it. We enjoy reading our article about Installing A Bathtub.
Click For More Info
Report this page